PROJECT INFO

SEPICN Type A+B T8 Tube

LED T8 tubes are now used widely for replacing linear fluorescent lamps in existing fixtures for commercial and industrial and educational lighting applications due to their energy efficiency, longer lifetime and lower maintenance cost. What most people may not understand is that not all LED T8’s are wired the same. Different LED T8 wiring design affects greatly the installation time and labor costs. In some cases projects can be delayed when the lamp holder configuration was not taken into account. In most projects the targeted fixtures have shunted lamp holders (estimated 60% fixtures in use have shunted lampholders). Using an LED T8 that can only work with a non-shunted lamp holder will increase the project cost with additional time (per fixture) on lamp holder replacement. SEPICN TYPE A & B LED T8 lamps are compatible with both non-shunted and shunted lamp holders. While other major LED T8 lamp manufacturers now provide extra parts (wirings and non-shunted lamp holders) needed to properly complete the project, this only adds to the cost of installation.

Construction & Materials

Lightweight Aluminum heat sink housing provides strength and Durability

Shatterproof Design

Suitable for use with non-shunted sockets and shounted sockets

Electrical System

Input Voltage:100-277V AC,50/60HZ Power Factor:>0.95 Power Efficiency:>88%

Compliance

SEPICN T8  Tubes are cETLus listed for damp locations -20°C – 55°C ambient environments

LED modules comply with IESNA LM-79 and LM-80 standards.

DesignLights Consortium™ Qualified and classified for DLC Standard (some models are not DLC qualified),

refer to www.designlights.org for details.

Super-easy Installation 

Just switch out the old fluorescent tubes for LEDs, and you’re done. No other modifications are required, but you must make sure your ballast is compatible with the LED T8 tubes you are trying to install.

Varying Light levels/energy consumption 

Fluorescent ballasts have varying ballast factors and since this type uses the existing fluorescent ballast, the wattage and lumen output will vary by ballast factor. Thus giving you the ability to increase or decrease energy consumption and light levels easily by using different ballasts.

Compatible with 90% ballast in North America market

SEPICN Type A+B can Compatible with 90% ballast in North America market.

COMPARISON OF LEADING T8 TUBES

Brand SEPCIN TYPE A/B T8 Philips Endural LED T8 Sylania Commercial Grade LED T8
Driver Type Internal Driver(Self Ballasted) Internal Driver(Self Ballasted) Internal Driver(Self Ballasted)
Retrofit Steps 1.Remove Fluorescent tube

2.Bypass Ballast

3.Install LED T8(using the original lamp holders)

1.Remove Fluorescent tube

2.Bypass Ballast

3.If shunted lamp holders,replace lamp holders with non-shunted lamp holders

4.Rewire input leads to lamp holders

5.Install LED T8

1.Remove Fluorescent tube

2.Bypass Ballast

3.If shunted lamp holders,replace lamp holders with non-shunted lamp holders

4.Rewire input leads to lamp holders

5.Install LED T8

Lamp Holders Compatible with shunted and non-shunted lamp holders,no need to change out Compatible only with non-shunted lamp holders,shunted lamp holders must be replaced Compatible only with non-shunted lamp holders,shunted lamp holders must be replaced
Per Fixtures retrofit time with 3 lamps Approx. 10mins Approx. 20-30mins Approx. 20-30mins

ORDERING INFO

Model Size Input Watt LEDS Efficacy Delivered Lumens Beam Angle
HC-T8-2FT-10W-ID-C-A 2FT 10W SMD2835 120Lumen/W 1200lms 120°
HC-T8-4FT-18W-ID-C-A/B 4FT 18W SMD2835 120Lumen/W 1960lms 120°
 HC-T8-4FT-13W-ID-C-A/B 4FT 13W SMD2835 145Lumen/W 1885lms 120°
 HC-T8-4FT-22W-ID-C-A/B 4FT 22W SMD2835 145Lumen/W 3190lms 120°

PACKING INFO

Model Unit weight(KGS) PCS/CTN G.W.(KGS) Size(MM)
2FT 0.4 25 9 650*220*220mm
4FT 0.68 25 16 1270*240*240mm